Find a store

Wilko 40mm Chrome Finish Universal Fit Waste Shower Tray Trap

0526314
£11.99
£11.99
Delivery
Unavailable
Click & Collect - Free

Collection in as little as 1 hour

No minimum spend

200+ wilko & The Range stores nationwide

How Click & Collect works

  • Choose your local store or collection point at The Range
  • Shop your favourites & pay online
  • We'll email you when your order is ready - this could be in as little as 1 hour
  • Pop to your local store, show the QR code & a team member will grab your items!

Product Information

  • Easy to fit and non-corrosive
  • Great for DIY and professional plumbers
  • Ideal replacement or for a new shower tray
Get that plumbing job done in no time with our quality chrome finish universal fit shower tray trap. Essential for both DIY and professional plumbers, the 40mm waste trap is an ideal replacement and a must-have when you're installing a new shower tray. Easy to fit, it is non-corrosive for lasting use. Directions for use: The Universal fit waste system is easily fitted to new and existing standard-sized waste pipes. Ensure the taps are fully closed. Disconnect existing pipework connected to the old trap. Note: Take care against any potential water spillage on removal. To ensure the best results, all pipes must be cut square and free of rough edges. All joints must be clean and free of any debris. To make an effective joint, you must, first of all, dismantle the joint fitting. Then place the locking ring and rubber washer onto the pipe. You must make sure the washer taper on the locking ring is facing the fitting. Insert the pipe fully into the joint (it will be approximately 1inch or 25mm). Then tighten the locking ring by hand, taking care not to over-tighten. When constructing a horizontal pipe run, you must make sure there is a fall to the final drain. A 2 ½ degree angle is recommended. Also, ensure pipe runs are supported by pipe clips every 1000mm for vertical runs and 500mm for horizontal runs.
Brand: wilko
Type: Bath, Sink and Shower Waste Traps
Colour: Multi
Pack Qty: 1
Size: 40mm
Customer Assembly Required: No
Height: 34.0CM
Width: 22.0CM
Depth: 9.0CM

Free Returns

Return this product for free within 14 days to The Range stores. Alternatively, contact customer services for more options.



View returns information

Shipped by the supplier

This product is only available online and sent directly to you from our supplier’s warehouse.

Delivery timescales may vary and will be accurately shown at checkout after entering your address.

Some postcode restrictions may apply, which can be found in the product information or after entering your address at checkout.

Our 14-day free returns policy applies to products shipped by our supplier but they cannot be returned in store.

Ideas & Advice

Ideas and Advice - Let's do it together

Loads of tips, hacks and how-tos to help you get your jobs done

Visit Ideas & Advice »

Product Information

  • Easy to fit and non-corrosive
  • Great for DIY and professional plumbers
  • Ideal replacement or for a new shower tray
Get that plumbing job done in no time with our quality chrome finish universal fit shower tray trap. Essential for both DIY and professional plumbers, the 40mm waste trap is an ideal replacement and a must-have when you're installing a new shower tray. Easy to fit, it is non-corrosive for lasting use. Directions for use: The Universal fit waste system is easily fitted to new and existing standard-sized waste pipes. Ensure the taps are fully closed. Disconnect existing pipework connected to the old trap. Note: Take care against any potential water spillage on removal. To ensure the best results, all pipes must be cut square and free of rough edges. All joints must be clean and free of any debris. To make an effective joint, you must, first of all, dismantle the joint fitting. Then place the locking ring and rubber washer onto the pipe. You must make sure the washer taper on the locking ring is facing the fitting. Insert the pipe fully into the joint (it will be approximately 1inch or 25mm). Then tighten the locking ring by hand, taking care not to over-tighten. When constructing a horizontal pipe run, you must make sure there is a fall to the final drain. A 2 ½ degree angle is recommended. Also, ensure pipe runs are supported by pipe clips every 1000mm for vertical runs and 500mm for horizontal runs.
Brand: wilko
Type: Bath, Sink and Shower Waste Traps
Colour: Multi
Pack Qty: 1
Size: 40mm
Customer Assembly Required: No
Height: 34.0CM
Width: 22.0CM
Depth: 9.0CM

You May Also Like

No Reviews Yet

Item removed from saved for later